LT Agreement Cle Elum - Laserfiche WebLink

Home Browse Search

Printed:6/27/2016 2:53:39 PM Q-2260-16.sbs Page 7 of Section 2 -Products and Fabrication Continued. 2.05 Accessories Countinued.. Slide Doors Sliding doors (for single-skin ribbed wali panels only)shall be single and/or double sliding doors constructed of cold-formed structural steel sheeted panel with amaximumopeningof24.00"wide x 20.0û"height. Door systems shall be provided with all tracks,trolleys,covering,trim,flashing,closures,locks,astragal plates and base guides necessary for field assembly of thedoorsystem. Sliding door sections shall be suspended by four-wheeled trolleys at each end sliding inside a track mounted on the exterior wall.Any structural exposed when door is closed shall be pre-galvanized steel fastened with plated fasteners.The jambs and header of the door opening shall be painted onecoatofredoxideshopcoat. Section 3 -Execution 3.01 Erection General: Erection shall be accomplished by a trained,competent erector having experience in erecting metal buildings. Install all metal building system components in strict compliance with Manufacturer's instructions shown on final shop drawings.Handle and store all materials to avoid damage and replace any damaged materials. Erector shall observe aiid follow recominendations of the Metal Building Manufacturers Association (MBMA),the American Institute of Steel Construction (AISC),and the Occupational Safety and Health Administration (OSHA)practices,procedures and safety standards where.applicable. Do not field cut or alter structural members without approval from Manufacturer. Structural Frames: Erect true to line,level and plumb,brace and secure with temporary bracing in all directions as required. Level base plates and secure to anchor rods to level plane with full bearing to foundation suppolting structures. Bracing: Install all permanent diagonal rod or angle bracing in roof and sidewalls as approved by Manufacturer. Properly tighten rods to avoid excessive sag. Roofing and Siding Panels: Install roof and canopy panels in such a manner to permit drainage to eaves of building,with panel ends square to eave.Install wall panels with vertical edges plumb. Arrange and nest sidelap joints away from prevailing winds when possible. Apply panels and associated items for neat and weathertight enclosure. Avoid "panel creep"or application not true to grid lines. Protect factory finishes from mechanical damage or abrasions. Install approved type closures to exclude weather. Install weather seal under ridge cap.Flash and seal roof panels at eave,gable and perimeter of all openings through roof and elsewhere as required or shown ondrawings. Flash and/or seul wall and liner panels at perimeter of all openings,under eaves and gable trims,along lower panel edges,and elsewhere as required or shown ondrawings,as applicable. Remove all fastener or cut shavings from roof and wall as erection is completed. Standing Seam Roof Panels: Install pancis with positive interlock between installation clips and standing seams in such a manner that will allow panels to support erection loads prior to closing ofseamswiuiseamer. Install concealed pariel clips (of sliding design to allow lbr expansion and contraclion inovement of partels)over top of roofing insulation along each standing seam atlocationandspacingdeierminedbymetalbuildingManufacturerandshownornhoManufa¢ttirefs drawings. Whore panel end splices occur,nest panels with end laps according to Manutocturer's instructions and install interlocking clamping plates and sealant.Make spliceindependentefstruciutetoallowforfreeexpansionandcon1ractionmovemeniofpunclswillioutsilessonsplice. Crimp standing seams with approved type motorized seamer tool to assure complete sealant engagement and to assure structural integrity of panel-to-panel andpanel-to-clip connections. Use fasteners penetrating mof panel olily at caves and end spiices (when required).At these conditions,use fasteners in conjunction with clamping plates (withfactory-punched holes to assure correct fastener placement)and approved type butyl scalant to assure positive watertight seals. Install ridge cover units of approved expansion joint design to accommodate expansion and contraction movement of roof panels without ponding at end splices.Coordinate installation of accessories and items to be mounted on metal roofing. Maintain proper panel coverage according to Manufacturer's instructions and drawings. Wall Panels: Install wall panels on exterior side of metal framing with liner panels installed on building interior in locations shown on drawings.Align bottoms of panels to proper coverage and fasten with Manufacturer's recommended and supplied fasteners. Cut and fasten flashing and trims with approved type fasteners. Install all fasteners with power tool having adequate torque and proper r.p.m.adjusted to seat fastener without damage to heads,washers or panels.Install panel sidelap away from prevailing wind or view direction when possible,maintaining proper lap without fastener dimpling or excessive overlap.