Laserfiche WebLink
feet (18.6 Jpt) ot endosed area, except that theSmartVENT" Stacking Modet #1S4dSf 1 andFloodVEN-t€ Stacking - Modei *tvluiit must beinstalled with a miniqnum of one FV for every400 square feet (37.2 m21 of enclosed area. <br />r Bebw the base flood elevation. <br />r With the boftom of lhe FV located a maximum of12 inches (305.4 mm) above the higher of the finalgrade or f,oor and finished exterior gfode immediately <br />under each opening. <br />4.2 Flood Vent Sealing Kit <br />The Flood Vent Seating Kft lrnodel 1140-526 is used in <br />conjunction with FloodVENf Modet #1f40_520. Wheninstatled and tested in accordance with ASTM E2g3, theFV and Flood Vent Sealing Kit assembly have an airleakage rate of less than 02 cubic feet fer minute perlineal fool (18.56 Umin per lineal meter) at a pressuredifferential of 1 pound per square foot (S'0 pa) based on <br />12.58_line.Et fg,et p.0 tineat miters) contained Oir me ftooOVert Sealing Kit. <br />5.0 coilDmoils oF usE <br />The Smart Vent@ FVs described in this report comply with, <br />or are suitable altematives lo wllat is specified in,-those <br />codes listed in Section 1.0 of this report, subject to thefollowing conditions: <br />5,1 The Smart Vont@ FVs musl be installed in accordancewith this report, the applicabte code and themanufacturer's installation instructions. ln the event ofa conflict, the instructions in thb report govem, <br />ESR-2074 I Most <br />For Sl: 1 inch = 28.4 mm; .t squaro foot = m? <br />and Trusted <br />TABL€ l_-ilODEL SIZES <br />2of5 <br />5.2 The Smart Vent@ FVs must not be used in the place <br />of "breakaway walls" in coastal high hazard areas, but <br />are permitted for use in conjunction with breakaway <br />walls in other areas. <br />6.0 EVIOENCESUBIIITTED <br />5"1 Data in accordance with the ICC-ES AcceptanceGriteria for Mechanically Operated Flood -Venls <br />$CS6+t, dated August 2015 (editoriaily revised <br />October 2017). <br />6.2 Test report on air infiltration in accordance wtth ASTM <br />E283. <br />7.0 IDENTIFICATION <br />?.i The $mart VEN14 models and the Flooct Vent Sealing <br />Kit recognized in lhis report must be identified by - <br />label bearing the manufacfurer's name {smartv-entProducts, lnc.), the model number, and the evaluagon <br />report number (ESR-2O74)- <br />7.2 The report holdefs conlact information is the <br />following: <br />SHART VENT PRODUCTS, INC. <br />rBOAI{DBRO DRIVE, UNIT 1 <br />PITMAII, ilEW JERSEY OSOTI <br />{877} 441€368 <br />\.{ri ry.Smartvent.com <br />info@smartyent.com <br />MODEL NAIIE MODEL I{UiIBER MODELSIZE (in.)COVERAGE (sq.ft) <br />1540-520 15%"x iT;200 <br />1540-510 1 x 200 <br />Overhead Door 1540-524 ts'tn"if h 200 <br />Overhead Door 1540-514 1s3lo" X73!o"200 <br />Wood Wall 1540-570 14" Xgat4"200Wood Wall Overhead Door 1549-574 14',X 200 <br />Slacker ts40-51 I 16'X 16"400 <br />Stacker 15/,0-521 16" X 16"400 <br />FIGURE l-SilART VENT: ilODEL .t540-st0